In-stock parts
Order by 2PM MST
In-stock parts
Order by 2PM MST
Images are for representation only and may differ from the actual product.
The Berkeley B69743 B4JRMBHS is a genuine Berkeley frame-mounted centrifugal pump configured for high-volume water-truck and dust-control systems. Its 5-inch suction and 4-inch discharge flanges support large plumbing systems, while the SAE C hydraulic-drive interface allows integration with a correctly sized hydraulic motor.
This clockwise-rotation configuration uses a 13.5-inch cast-iron impeller and mechanical shaft seal. At 2,400 RPM with fresh water at 68°F, the published selection reaches its best-efficiency point at approximately 1,546 GPM and 290.5 feet of head (about 126 PSI).
| Feature | Configuration |
|---|---|
| Manufacturer | Berkeley |
| Model | B4JRMBHS |
| Manufacturer Part Number | B69743 |
| Pump Type | Frame-mounted centrifugal water pump |
| Specification | Value |
|---|---|
| Suction | 5-inch flange |
| Discharge | 4-inch flange |
| Rotation | Clockwise (CW), viewed from the shaft end |
| Impeller | 13.5-inch cast iron |
| Shaft Seal | Mechanical seal |
| Construction | All iron |
| Performance Item | Published Value |
|---|---|
| Best-Efficiency Flow | 1,545.7 GPM |
| Head at Best-Efficiency Point | 290.5 ft (approximately 125.8 PSI) |
| Maximum Head | 354.9 ft (approximately 153.6 PSI) |
| Efficiency at Rated Point | 79.9% |
| Minimum Continuous Stable Flow | 482.7 GPM |
| NPSH Required at Rated Point | 10.8 ft |
| Connection | Configuration |
|---|---|
| Drive | Hydraulic coupling drive |
| Published Speed Range | 1,400-2,400 RPM |
| Motor Mount | SAE C, 4-bolt |
| Shaft Interface | 1-1/4-inch, 14-tooth spline |
| Recommended Power at 2,400 RPM Selection | 150 HP / 112 kW |
| Application | Selection Guidance |
|---|---|
| Water trucks | High-volume spray, fill and transfer systems using compatible 5-inch x 4-inch flanged plumbing |
| Dust control | Match pump speed and hydraulic power to the complete plumbing and spray-system demand |
| Replacement | Verify the Berkeley model, B/M number, impeller diameter and nameplate data before ordering |
| Installation | Support and align piping independently; prime before startup and never run dry |
Confirm the pump nameplate, clockwise rotation, 5-inch x 4-inch flanged connections, SAE C 4-bolt motor mount, 1-1/4-inch 14-tooth spline, and mechanical-seal configuration. Published performance is based on fresh water at 68°F and will vary with pump speed, suction conditions, plumbing and total system resistance. Do not operate above the published 2,400 RPM hydraulic-drive range.
| Manufacturer part number | B69743 |
|---|---|
| Model Number | B4JRMBHS |
| Material | Cast Iron |
| Size | 5" x 4" |
| Connection | Flange |
| Seal Type | Mechanical Seal |
| Seal Material | Ceramic |
| Rotation | Clockwise (CW) |
| Weight | 326.0 lb |
B69743 (B4JRMBHS) · March 4, 2013
Volute Case
Used in assembly: To verify
View product and purchase optionsImpeller
Used in assembly: To verify
View product and purchase optionsShaft
Used in assembly: To verify
Request a quote. Enable JavaScript to prepare a draft from this part.
Wear Ring
Used in assembly: To verify
View product and purchase optionsMechanical Shaft Seal Retainer
Used in assembly: To verify
View product and purchase optionsShaft Sleeve
Used in assembly: To verify
Request a quote. Enable JavaScript to prepare a draft from this part.
Impeller-End Bearing
Used in assembly: To verify
View product and purchase optionsDrive-End Ball Bearing
Used in assembly: To verify
View product and purchase optionsBearing Frame
Used in assembly: To verify
Request a quote. Enable JavaScript to prepare a draft from this part.
Impeller Screw, 1/2-13 × 1-1/2 in.
Used in assembly: To verify
View product and purchase optionsInner Bearing Cap
Used in assembly: To verify
View product and purchase optionsOuter Bearing Cap
Used in assembly: To verify
Request a quote. Enable JavaScript to prepare a draft from this part.
Water Slinger
Used in assembly: To verify
View product and purchase optionsDrive-End Oil Seal
Used in assembly: To verify
View product and purchase optionsImpeller-End Oil Seal
Used in assembly: To verify
View product and purchase optionsImpeller Washer
Used in assembly: To verify
View product and purchase optionsThrust Ring
Used in assembly: To verify
View product and purchase optionsVolute Gasket
Used in assembly: To verify
View product and purchase optionsBalance Ring Gasket
Used in assembly: To verify
View product and purchase optionsMechanical Shaft Seal
Used in assembly: To verify
View product and purchase optionsBalance Ring
Used in assembly: To verify
View product and purchase optionsO-Ring
Used in assembly: To verify
View product and purchase optionsHex Cap Screw, 5/8-11 × 1-1/2 in.
Used in assembly: 12
Request a quote. Enable JavaScript to prepare a draft from this part.
Square Head Bolt, 1/2-13 × 2-1/4 in.
Used in assembly: 2
Request a quote. Enable JavaScript to prepare a draft from this part.
Stud, 3/8-16 × 1-1/2 in.
Used in assembly: 4
Request a quote. Enable JavaScript to prepare a draft from this part.
Hex Nut, 3/8-16
Used in assembly: 4
View product and purchase optionsHex Nut, 1/2-13 × 7/16 in.
Used in assembly: 2
View product and purchase optionsLock Washer
Used in assembly: To verify
View product and purchase optionsPipe Plug, 1/2 NPT
Used in assembly: 4
Request a quote. Enable JavaScript to prepare a draft from this part.
Pipe Plug, 1/4 NPT
Used in assembly: To verify
Request a quote. Enable JavaScript to prepare a draft from this part.
Grease Fitting
Used in assembly: 2
View product and purchase optionsRetaining Ring
Used in assembly: To verify
View product and purchase optionsRetaining Ring
Used in assembly: To verify
View product and purchase optionsYour selected parts and requested quantities will appear below when the quote form is ready.